# CircuitSetup 6 Channel Energy Meter 3rd Add-on board config
# Assumes jumpers are both in the 3rd position

sensor:
#IC1 AddOn 3
############
  - platform: atm90e32
    release_device: true
    #if ESP32 has an LED for GPIO2, remove jumper or ESP32 from meter stack before programming via serial
    cs_pin: ${addon3_ic1}
    id: ${addon3_id1}
    phase_a:
      current:
        name: ${ct19_name} ${amp_label}
        id: ct19Amps
        entity_category: diagnostic
        accuracy_decimals: ${amp_accuracy_decimals}
        filters:
          # Drop noise below 0.02A, then log 0.05A changes or every 60s
          - lambda: "return x < 0.02 ? 0 : x;"
          - or:
              - delta: ${amp_delta}
              - throttle: ${amp_throttle}
      power:
        name: ${ct19_name} ${watt_label}
        id: ct19Watts
        accuracy_decimals: 1
        filters:
          # Convert negative to positive (absolute value)
          - lambda: "return abs(x);"
          # Clip "ghost" watts when the device is off
          - lambda: "return x < 5.0 ? 0 : x;"
          - or:
              - delta: ${watt_delta_lights}
              - throttle: ${watt_throttle}
      gain_voltage: ${voltage_cal1}
      gain_ct: ${current_cal_ct19}
    phase_b:
      current:
        name: ${ct20_name} ${amp_label}
        id: ct20Amps
        entity_category: diagnostic
        accuracy_decimals: ${amp_accuracy_decimals}
        filters:
          # Drop noise below 0.02A, then log 0.05A changes or every 60s
          - lambda: "return x < 0.02 ? 0 : x;"
          - or:
              - delta: ${amp_delta}
              - throttle: ${amp_throttle}
      power:
        name: ${ct20_name} ${watt_label}
        id: ct20Watts
        accuracy_decimals: 1
        filters:
          # Convert negative to positive (absolute value)
          - lambda: "return abs(x);"
          # Clip "ghost" watts when the device is off
          - lambda: "return x < 5.0 ? 0 : x;"
          - or:
              - delta: ${watt_delta_lights}
              - throttle: ${watt_throttle}
      gain_voltage: ${voltage_cal1}
      gain_ct: ${current_cal_ct20}
    phase_c:
      current:
        name: ${ct21_name} ${amp_label}
        id: ct21Amps
        entity_category: diagnostic
        accuracy_decimals: ${amp_accuracy_decimals}
        filters:
          # Drop noise below 0.02A, then log 0.05A changes or every 60s
          - lambda: "return x < 0.02 ? 0 : x;"
          - or:
              - delta: ${amp_delta}
              - throttle: ${amp_throttle}
      power:
        name: ${ct21_name} ${watt_label}
        id: ct21Watts
        accuracy_decimals: 1
        filters:
          # Convert negative to positive (absolute value)
          - lambda: "return abs(x);"
          # Clip "ghost" watts when the device is off
          - lambda: "return x < 5.0 ? 0 : x;"
          - or:
              - delta: ${watt_delta_lights}
              - throttle: ${watt_throttle}
      gain_voltage: ${voltage_cal1}
      gain_ct: ${current_cal_ct21}
    line_frequency: ${electric_freq}
    gain_pga: 1X
    update_interval: ${update_time}
    enable_offset_calibration: ${offset_calibration}
    enable_gain_calibration: ${gain_calibration}
#IC2 AddOn 3
############
  - platform: atm90e32
    release_device: true
    cs_pin: ${addon3_ic2}
    id: ${addon3_id2}
    phase_a:
      current:
        name: ${ct22_name} ${amp_label}
        id: ct22Amps
        entity_category: diagnostic
        accuracy_decimals: ${amp_accuracy_decimals}
        filters:
          # Drop noise below 0.02A, then log 0.05A changes or every 60s
          - lambda: "return x < 0.02 ? 0 : x;"
          - or:
              - delta: ${amp_delta}
              - throttle: ${amp_throttle}
      power:
        name: ${ct22_name} ${watt_label}
        id: ct22Watts
        accuracy_decimals: 1
        filters:
          # Convert negative to positive (absolute value)
          - lambda: "return abs(x);"
          # Clip "ghost" watts when the device is off
          - lambda: "return x < 5.0 ? 0 : x;"
          - or:
              - delta: ${watt_delta_lights}
              - throttle: ${watt_throttle}
      gain_voltage: ${voltage_cal2}
      gain_ct: ${current_cal_ct22}
    phase_b:
      current:
        name: ${ct23_name} ${amp_label}
        id: ct23Amps
        entity_category: diagnostic
        accuracy_decimals: ${amp_accuracy_decimals}
        filters:
          # Drop noise below 0.02A, then log 0.05A changes or every 60s
          - lambda: "return x < 0.02 ? 0 : x;"
          - or:
              - delta: ${amp_delta}
              - throttle: ${amp_throttle}
      power:
        name: ${ct23_name} ${watt_label}
        id: ct23Watts
        accuracy_decimals: 1
        filters:
          # Convert negative to positive (absolute value)
          - lambda: "return abs(x);"
          # Clip "ghost" watts when the device is off
          - lambda: "return x < 5.0 ? 0 : x;"
          - or:
              - delta: ${watt_delta_lights}
              - throttle: ${watt_throttle}
      gain_voltage: ${voltage_cal2}
      gain_ct: ${current_cal_ct23}
    phase_c:
      current:
        name: ${ct24_name} ${amp_label}
        id: ct24Amps
        entity_category: diagnostic
        accuracy_decimals: ${amp_accuracy_decimals}
        filters:
          # Drop noise below 0.02A, then log 0.05A changes or every 60s
          - lambda: "return x < 0.02 ? 0 : x;"
          - or:
              - delta: ${amp_delta}
              - throttle: ${amp_throttle}
      power:
        name: ${ct24_name} ${watt_label}
        id: ct24Watts
        accuracy_decimals: 1
        filters:
          # Convert negative to positive (absolute value)
          - lambda: "return abs(x);"
          # Clip "ghost" watts when the device is off
          - lambda: "return x < 5.0 ? 0 : x;"
          - or:
              - delta: ${watt_delta_lights}
              - throttle: ${watt_throttle}
      gain_voltage: ${voltage_cal2}
      gain_ct: ${current_cal_ct24}
    line_frequency: ${electric_freq}
    gain_pga: 1X
    update_interval: ${update_time}
    enable_offset_calibration: ${offset_calibration}
    enable_gain_calibration: ${gain_calibration}

# #Total A AddOn3
#   - platform: template
#     name: Add-on 3 Total ${amp_label}
#     id: totalAmpsAddOn3
#     lambda: return id(ct19Amps).state + id(ct20Amps).state + id(ct21Amps).state + id(ct22Amps).state + id(ct23Amps).state + id(ct24Amps).state ;
#     accuracy_decimals: 2
#     unit_of_measurement: A
#     device_class: current
#     update_interval: ${update_time}

# #Total W AddOn3
#   - platform: template
#     name: Add-on 3 Total ${watt_label}
#     id: totalWattsAddOn3
#     lambda: return id(ct19Watts).state + id(ct20Watts).state + id(ct21Watts).state + id(ct22Watts).state + id(ct23Watts).state + id(ct24Watts).state ;
#     accuracy_decimals: 2
#     unit_of_measurement: W
#     device_class: power
#     update_interval: ${update_time}

  #kWh From CT 19
  - platform: total_daily_energy
    name: ${ct19_name} ${kwh_label}
    id: ct19Kwh
    power_id: ct19Watts
    filters:
      - multiply: 0.001
      - throttle: ${kwh_throttle}
    unit_of_measurement: kWh
    device_class: energy
    state_class: total_increasing

  # kWh from CT 20
  - platform: total_daily_energy
    name: ${ct20_name} ${kwh_label}
    id: ct20Kwh
    power_id: ct20Watts
    filters:
      - multiply: 0.001
      - throttle: ${kwh_throttle}
    unit_of_measurement: kWh
    device_class: energy
    state_class: total_increasing

  #kWh From CT 21
  - platform: total_daily_energy
    name: ${ct21_name} ${kwh_label}
    id: ct21Kwh
    power_id: ct21Watts
    filters:
      - multiply: 0.001
      - throttle: ${kwh_throttle}
    unit_of_measurement: kWh
    device_class: energy
    state_class: total_increasing

  #kWh From CT 22
  - platform: total_daily_energy
    name: ${ct22_name} ${kwh_label}
    id: ct22Kwh
    power_id: ct22Watts
    filters:
      - multiply: 0.001
      - throttle: ${kwh_throttle}
    unit_of_measurement: kWh
    device_class: energy
    state_class: total_increasing

  #kWh From CT 23
  - platform: total_daily_energy
    name: ${ct23_name} ${kwh_label}
    id: ct23Kwh
    power_id: ct23Watts
    filters:
      - multiply: 0.001
      - throttle: ${kwh_throttle}
    unit_of_measurement: kWh
    device_class: energy
    state_class: total_increasing

  #kWh From CT 24
  - platform: total_daily_energy
    name: ${ct24_name} ${kwh_label}
    id: ct24Kwh
    power_id: ct24Watts
    filters:
      - multiply: 0.001
      - throttle: ${kwh_throttle}
    unit_of_measurement: kWh
    device_class: energy
    state_class: total_increasing